Cross stitch guides › How to frame cross stitch
How to frame cross stitch
Framing is three decisions and one evening of work. Decide the size, decide whether there is a mat, decide whether there is glass; then stretch the fabric over a board so that it stays flat for decades. This page takes them in that order.
Before you start
Wash and press the piece first. Marks that are invisible now turn yellow behind glass in a few years, and a crease framed is a crease forever. Do not trim the fabric: every inch of margin makes the next steps easier.
Working out the size
Everything follows from the stitched area, which is the stitch count divided by the stitches to the inch.
- Stitched area. A design of 140 by 112 stitches on 14 count is 140 ÷ 14 = 10 inches by 112 ÷ 14 = 8 inches.
- The opening. With a mat, show a quarter of an inch of bare fabric round the stitching: 10.5 by 8.5 inches. Without a mat, show at least an inch all round, or the design looks squeezed.
- The frame. Add the mat on every side. A 2 inch mat makes it 14.5 by 12.5 inches.
- Check the shops. Ready-made frames come in set sizes, and the nearest may need a slightly different mat.
The frame size calculator does all four steps for your own pattern, finds the nearest ready-made frame, tells you the mat that leaves, and checks whether your fabric is big enough to lace.
What goes in the frame
- Board. Acid-free mount board or foam board. Ordinary cardboard yellows the fabric over time.
- Mat (window mount). Optional, but it does two jobs: it sets the piece off, and it holds the glass away from the stitching.
- Glass. Also optional. It keeps out dust, smoke and fingers. Without a mat, use spacers under the frame’s lip so the glass does not flatten the stitches. Pieces with beads or many French knots are often left unglazed.
- Frame depth. The fabric folded over the board is thicker than a photograph. Check that the recess at the back of the frame is deep enough for board, fabric, mat and glass together.
Lacing: the method that lasts
There are quicker ways to fix fabric to a board: pins, tape, sticky board. Lacing takes longer and is the one to use for anything you care about, for three reasons. It uses only thread, so nothing sticky ever touches the fabric. It can be tightened or undone at any time. And it pulls evenly from edge to edge, so the weave stays straight.
- Cut the board. To fit the frame if there is no mat. Under a mat, half an inch larger than the opening on every side is enough.
- Mark the middles. Pencil a mark at the center of each edge of the board. Find the center of each edge of the stitching by counting.
- Center the piece. Lay the stitching face up on the board, match the centers, and push a pin into the edge of the board at each of the four marks. Add pins along each edge, working from the middle outward, following one line of holes in the fabric so that the weave runs straight.
- Turn it over onto a clean towel and fold the two long edges of fabric to the back.
- Lace side to side. Thread a needle with strong thread straight from the reel, without cutting it. Starting at the middle, take a stitch in one flap, cross to the other, take a stitch there, and work toward one end in a zigzag. Go back to the middle and lace toward the other end. Stitches about an inch apart are close enough.
- Tighten. Starting from the fixed end, pull up the slack one stitch at a time, as you would a shoelace, until the front is flat and firm but not stretched. Fasten off.
- Fold in the other two edges and lace top to bottom in the same way. At the corners, fold the fabric flat like the end of a parcel and catch it with a few stitches.
- Take out the pins and check the front. If a line of the weave bows, loosen the lacing on that side and tighten the other.
How much fabric lacing needs
The fabric has to reach round the edge of the board with enough left to take the stitches: at least an inch and a half beyond the mat opening on every side. That is why the usual advice is to leave 3 inches round a design that will be framed. If your margins are narrower, sew a strip of plain cotton to each edge and lace through that. The fabric margin planner gives the margin for every way of finishing, before you cut.
Thread for lacing
Use something strong that does not stretch: buttonhole thread, quilting thread or crochet cotton. Ordinary sewing thread can snap as you tighten it. Take the thread from the reel as you go: you will need several times the width of the piece, and a join in the middle is a weak point.
Into the frame
- Clean the inside of the glass and let it dry.
- Lay in the glass, then the mat or spacers, then the laced piece, face down.
- Add the backing board and fix it with the frame’s tabs or with framer’s points.
- Seal the back with paper tape to keep out dust and insects.
Hang it out of direct sun. All thread dyes fade in strong light, and glass alone does not stop that.
When to use a framer
For a piece that took months, a professional framer is worth the money: ask for lacing, acid-free materials and spacers or a mat, and say that the fabric must not be glued or trimmed. For small pieces, a hoop finish is quicker and cheaper than any frame.
Mistakes that are easy to avoid
- Sticking it down. Adhesive boards and tape are fast and cannot be undone. Adhesives discolor with age and take the fabric with them.
- Glass on the stitches. It flattens them, and any damp inside the frame is held against the thread.
- Trimming first. Cut nothing until the piece is laced and you can see what is spare.
- Pulling too tight. Over-stretched fabric distorts the design and strains the weave. Flat and firm is enough.
- Buying the frame by the fabric size. Measure the stitching, then add the border you want to see.
Questions people ask
What is the best way to frame cross stitch?
Lace it over acid-free board, and keep the glass off the stitches with a mat or spacers. Nothing is glued, so it can always be undone.
Should cross stitch be framed with glass?
Glass protects against dust and dirt and is a good idea in kitchens and bathrooms. It must not touch the stitching. Pieces with raised work are often framed without it.
What size frame do I need?
The stitched area, plus the fabric you want to show, plus the mat on every side. The frame size calculator works it out from the stitch count.
How much fabric do I need to leave for framing?
Three inches on every side of the stitching is the safe rule. Lacing needs at least an inch and a half beyond the mat opening.
Can I use sticky board?
It works for a quick piece you do not mean to keep for decades. For anything that matters, lace it: adhesive cannot be removed later.
More guides
- How to wash and pressClean a finished piece and press it without flattening the stitches.
- Finishing in a hoopMount a finished piece in a hoop with a neat, covered back.
- How to cross stitchThe whole craft from the first stitch to the last, for complete beginners.
- Fabric count explainedWhat 14 count means, and how count changes the size of everything.
- Aida, evenweave and linenHow the three fabrics differ and which to choose.
- How to find the centerTwo reliable ways to start in the middle so the design sits straight.
- Cross stitch glossary58 terms in plain words.