StitchAndGrid My projects Make a pattern

Cross stitch guides › How to find the center

How to find the center of cross stitch fabric

Starting in the center is the simple way to make sure a design sits in the middle of its fabric with an even border all round. It takes one minute.

Find the center of the fabric

centerfold 1fold 2where the design will sit
Fold in half one way, then the other. The folds cross at the center.
  1. Fold the fabric in half, short edges together, and pinch a soft crease along the fold.
  2. Open it and fold it in half the other way. Pinch again.
  3. Open it flat. The two creases cross at the center. Mark it with a pin, or a single loose stitch in a pale thread that you will pull out later.

If you fold often, a center-finding ruler is quicker: it has zero in the middle and counts outward both ways, so you slide it until both edges of the fabric read the same number. Tying a short length of bright thread through the center hole marks it better than a pin, which can fall out.

Pinch gently. A hard crease in Aida can be slow to press out. Never mark the center with pen or pencil unless it is a marker made to wash out of fabric.

Find the center of the chart

Most charts print a small arrow on the top edge and another on the side. Follow each arrow in a straight line; where the two lines meet is the center. The charts from our text generator and alphabet pages have these arrows.

No arrows? Halve the stitch count each way. A design 100 wide and 80 high has its center 50 stitches in from the left and 40 down from the top.

Make the first stitch

The center of the chart is often an empty square. That is fine: count from the center to the nearest stitched square on the chart, count the same number of holes on the fabric, and begin there. Starting with a block of one color near the middle is easier than starting with a single lonely stitch.

The other way: start from a corner

Some people prefer to begin at the top-left and work down, especially on large full-coverage pieces. To do that safely, work out the margin first:

  • Margin at each side = (fabric width − design width) ÷ 2.
  • Margin top and bottom = (fabric height − design height) ÷ 2.

Example: a design 7.1 inches wide on fabric 13.1 inches wide leaves (13.1 − 7.1) ÷ 2 = 3 inches each side. Measure 3 inches in from the left edge and 3 down from the top, and make your first stitch there. The fabric calculator gives both the design size and the fabric size.

For big designs: grid the fabric

On a large piece, finding the center is only the start. Gridding means marking the fabric every ten stitches to match the bold lines of the chart, so you never count more than nine squares at a time.

  • With thread: run a line of long tacking stitches in a smooth thread along every tenth row and column, and pull them out as you reach them.
  • With a washable fabric pen: draw the lines lightly. Always test the pen on a spare corner of the same fabric and wash it out first, because the stiffening in some Aida holds ink.
  • Pre-gridded fabric has the lines printed on and washes clean.

Start from the center and grid outward, so the grid on the fabric lines up with the grid on the chart.

If you have already started in the wrong place

Do not unpick anything yet. Count how many stitches the design still needs in the direction that looks short, convert that to inches with the fabric calculator, and measure what is left.

  • Enough fabric with at least 1.5 inches (4 cm) to spare: carry on. The design will sit off center on the cloth, but a hoop or a frame is centered on the stitching, not the fabric, so nobody will know.
  • Fabric to spare, but under 1.5 inches: plan to frame it with a mount, or finish it as a card or small cushion, where a narrow edge is enough.
  • Not enough fabric: stop now and restart on a new piece. It costs less time than finishing something that cannot be mounted.

Mistakes that are easy to avoid

  • Folding fabric that is not cut square. Trim along a line of holes first so the edges are straight.
  • Forgetting the design may not be symmetrical. The center of the stitch count is the center, even if the picture looks heavier on one side.
  • Trusting the center on a large piece. On big designs, also check that the fabric is large enough: count out to the widest point before you commit.

Questions people ask

Do I have to start in the center?

No, but it is the safest way. Starting at a corner works as long as you measure the margin first.

What if my fabric has an odd number of holes?

Being half a stitch off center cannot be seen. Pick either side and carry on.

How much fabric should be left around the design?

Three inches (7.5 cm) on each side for framing, two for a hoop.

More guides