StitchAndGrid My projects Make a pattern

Cross stitch guides › Starting and ending a thread

How to start and end a thread in cross stitch

Knots make bumps that show through the front and can work loose in the wash. These methods hold the thread just as firmly and leave the back flat.

The loop start (the neatest, for two strands)

the loopboth cut ends in the needleOne strand, twice the usual length, folded in half = two strands
One long strand folded in half gives two strands with a loop at one end.
  1. Cut one strand twice as long as usual, about 36 inches (90 cm).
  2. Fold it in half and thread the two cut ends through the needle. The loop hangs at the other end.
  3. Bring the needle up where the stitch begins, leaving the loop at the back.
  4. Go down to make the first leg, and on the back pass the needle through the loop.
  5. Pull gently. The loop locks the thread with no knot and no tail.

Not sure how many strands your fabric takes? The needle and strands chart lists every fabric. The loop start works with any even number of strands. It does not work with one or three strands, or with thread whose color changes along its length, because folding it reverses half of it.

The tail start (works with any number of strands)

  1. Bring the needle up, leaving about an inch (2.5 cm) of thread at the back.
  2. Hold the tail flat against the back, lying in the direction you are about to stitch.
  3. Make your first few stitches so that the thread crossing the back traps the tail.
  4. After three or four stitches, trim what is left.

Starting next to stitches you have already made

Slide the needle under three or four stitches on the back, close to where you want to begin, then come up and carry on. This is the quickest start once a piece is under way.

The waste knot (for a first stitch in open fabric)

Knot the end, and take the needle down from the front a couple of inches away along the line you will stitch. Stitch toward the knot so the thread on the back is covered, then snip the knot off the front.

The pin stitch (for a single stitch on its own)

A lone stitch has no neighbors to hide a tail under. A pin stitch anchors the thread with one or two tiny stitches made inside the square the cross will cover, so the cross itself hides them. It takes practice and is used most on designs with many scattered single stitches. If your pattern has only a few, a loop start does the same job more easily.

Which start to use

Your situationBest start
Two strands (or any even number), new areaLoop start
One or three strands, new areaWaste knot, or the tail start
Next to stitches already madeSlide under the backs of those stitches
Thread whose color changes along its lengthTail start or waste knot, never a loop start
Dark thread on pale fabricLoop start, or bury the tail under stitches of the same color
One stitch on its ownLoop start, or a pin stitch

Ending a thread

  1. Stop while there is still enough thread to handle easily: about 3 inches (8 cm).
  2. Turn the work over. Slide the needle under three or four stitches on the back, preferably of the same color.
  3. Pull through and trim close.

Keeping the back tidy

  • Do not carry a thread across bare fabric. It can show from the front, especially dark thread on light fabric. End it and start again.
  • Short hops are fine. Up to three or four stitches across the back, under existing stitches, is safe.
  • Dark under dark. Finish dark threads under dark stitches so nothing shadows through pale areas.

Questions people ask

Why should I not use knots?

They make lumps under the fabric that show when the piece is framed flat, and they can pull through the holes.

How long should my thread be?

About 18 inches (45 cm) in use. For a loop start cut twice that and fold it.

Does the back have to be neat?

It has to be flat. A flat back mounts well; a perfect back is only for show.

More guides