Cross stitch guides › How to backstitch
How to backstitch in cross stitch
Backstitch is the line stitch of cross stitch. It draws the outlines, whiskers, stems and small lettering that crosses are too coarse to show. It is easy, and the same few habits make it neat.
When to do it
Last. Finish every cross stitch in an area before adding backstitch near it. The lines lie on top of the crosses and often run along their edges, and a cross made afterwards would push the line out of place or cover it. DMC’s own advice is the same: add backstitch after the cross stitches, because it can overlap them.
What you need
- The same needle. A tapestry needle works for backstitch along the holes. For a line that has to pierce the middle of an Aida block, a sharp needle is easier.
- One strand. A single strand gives a fine, crisp line, and it is what most charts intend. Use two strands only where the key asks for a heavier line, or on 11 count where one strand looks thin. The needle and strands chart gives the usual numbers for each fabric.
- A shorter thread. About 12 inches (30 cm). A single strand frays and knots sooner than two.
The stitch, step by step
- Secure the thread by running it under three or four cross stitches on the back, near where the line begins.
- Make the first stitch: come up where the line starts and go down one square along.
- Come up one square ahead of the line, at the hole beyond where you just went down.
- Go back down at the end of the previous stitch, in the same hole. This backward step is what gives the stitch its name, and what makes the line unbroken.
- Repeat: up one square ahead, back down into the last hole.
- Finish by running the thread under several stitches on the back. Do not carry it across bare fabric; a dark thread shows through.
Each stitch covers one side of one square. Keeping every stitch that length is the whole secret of an even line.
Corners, slants and long stitches
- Corners. End a stitch exactly at the corner hole and start the next from it. Do not cut the corner with a slanted stitch unless the chart shows one.
- Diagonals. A line at 45 degrees crosses one square corner to corner. Work it one square at a time, as you would a straight line.
- Shallow slants. Charts often draw a line across two squares and up one. That is one long stitch from hole to hole, not two short ones: follow the chart’s line ends.
- Curves. On Aida a curve is made of short straight stitches. For a smoother curve, DMC suggests piercing the fabric between the holes, or stitching on evenweave, where there is a hole in the middle of every stitch.
- Very long stitches (whiskers, flower stems) sag. Break anything over three squares into shorter stitches, or catch it down in the middle with a tiny stitch.
Reading backstitch on a chart
Backstitch is drawn as a solid line over the symbols, running from hole to hole, usually in a color that the key lists separately with its own thread number and strand count. Where two lines of different colors meet, the key tells them apart by color or by line style. How to read a chart covers the rest of the page.
The PDFs made on this site list backstitch on its own row of the color key with its own thread estimate, and the pattern maker lets you draw backstitch between any two holes.
Choosing the color
Black is the habit, and it is often too harsh. An outline in a darker shade of the color it surrounds, a dark red round a red heart or a deep green round a leaf, defines the shape without looking like a drawing in ink. DMC gives the same tip. Keep black for eyes, lettering and anything meant to look drawn. The DMC color chart shows each family from light to dark, which makes picking the darker neighbor quick.
Backstitch lettering
Small words are often clearer in backstitch than in crosses: a name can be four squares tall and still be read. Our Backstitch 4 alphabet is drawn so that every stroke runs from hole to hole, and the text generator charts any words in it.
Mistakes that are easy to avoid
- Backstitching as you go. Lines stitched before the crosses round them get buried or bent. Leave them to the end.
- Pulling too tight. A tight backstitch sinks between the crosses and puckers the fabric. The thread should lie on the surface.
- Stitches of uneven length. One long stitch among short ones catches the eye. One square a stitch, unless the chart says otherwise.
- Running stitch by mistake. If you always move forward and never step back, you leave gaps. Each stitch must end in the hole where the last one began.
- Trailing thread across the back. Jumps between two outlines show through pale fabric. Finish off and start again.
Questions people ask
How many strands for backstitch?
One, in most patterns. Use two only if the key says so or the line looks too faint on a low count fabric.
Do I backstitch before or after the cross stitches?
After. Finish all the crosses in an area first, then add the lines on top.
Can I leave the backstitch out?
You can, but the design usually loses its detail: faces lose their features and pale shapes lose their edges. Try the outline on one part before deciding.
What is the difference between backstitch and Holbein stitch?
Both make a solid line. Holbein stitch, or double running stitch, goes along the line in running stitch and comes back filling the gaps, which leaves the back as neat as the front. It is the stitch of blackwork.
Why does my backstitch look wobbly?
Usually uneven tension or stitches of different lengths. Keep each stitch one square long and let the thread lie flat.
Where the facts come from
That backstitch is added after the cross stitches, the single strand for fine outlines, piercing Aida or using evenweave for curves, darker shades in place of black, and the warning about tension are DMC’s own advice, from its page “Use back stitch to accentuate your cross stitch”, read 17 November 2026.
More guides
- How to do a French knotThe four moves, why knots vanish, and what to use if you dislike them.
- Half, quarter and three-quarter stitchesPart stitches: what each one is, how charts show them, and two threads in one square.
- How to cross stitchThe whole craft from the first stitch to the last, for complete beginners.
- Fabric count explainedWhat 14 count means, and how count changes the size of everything.
- Aida, evenweave and linenHow the three fabrics differ and which to choose.
- How to find the centerTwo reliable ways to start in the middle so the design sits straight.
- Cross stitch glossary58 terms in plain words.